? ? 思路來源：
??? 從publish 表中取出第 n 條到第 m 條的記錄：?
??? SELECT TOP m-n+1 *?
????? FROM publish?
????? WHERE (id NOT IN?
????????????? (SELECT TOP n-1 id?
　　　　???????? FROM publish))

??? 存儲過程：

CREATE PROCEDURE pagination3
@tblName varchar(255) , -- 表名
@strGetFields varchar(1000) = '*', -- 需要返回的列?
@fldName varchar(255)='', -- 排序的字段名
@PageSize int = 10, -- 頁尺寸
@PageIndex int = 1, -- 頁碼
@doCount bit = 0, -- 返回記錄總數, 非 0 值則返回
@OrderType bit = 0, -- 設置排序類型, 非 0 值則降序
@strWhere varchar(1500) = '' -- 查詢條件 (注意: 不要加 where)
AS

declare @strSQL varchar(5000) -- 主語句
declare @strTmp varchar(110) -- 臨時變量
declare @strOrder varchar(400) -- 排序類型

if @doCount != 0
?? begin
????? if @strWhere !=''
???????? set @strSQL = 'select count(*)? Total from? where '+@strWhere
????? else
???????? set @strSQL = 'select count(*)? Total from '
?? end?
--以上代碼的意思是如果@doCount傳遞過來的不是0，就執行總數統計。以下的所有代碼都是@doCount為0的情況：

else
?? begin
????? if @OrderType != 0
???????? begin
??????????? set @strTmp = '<(select min'
??????????? set @strOrder = ' order by [' + @fldName +'] desc'
???????? --如果@OrderType不是0，就執行降序，這句很重要！

???????? end
????? else
???????? begin
??????????? set @strTmp = '>(select max'
??????????? set @strOrder = ' order by [' + @fldName +'] asc'
???????? end

???? if @PageIndex = 1
??????? begin
?????????? if @strWhere != ''

????????????? set @strSQL = 'select top ' + str(@PageSize) +' '+@strGetFields+ ' from [' + @tblName + '] where ' + @strWhere + ' ' + @strOrder
?????????? else

????????????? set @strSQL = 'select top ' + str(@PageSize) +' '+@strGetFields+ ' from ['+ @tblName + '] '+ @strOrder
????? --如果是第一頁就執行以上代碼，這樣會加快執行速度
??????? end
???? else
???????? begin
?????????? set @strSQL = 'select top ' + str(@PageSize) +' '+@strGetFields+ ' from ['
??????????????????????? + @tblName + '] where [' + @fldName + ']' + @strTmp + '(['
??????????????????????? + @fldName + '])　from (select top ' + str((@PageIndex-1)*@PageSize) + ' ['
??????????????????????? + @fldName + '] 　from [' + @tblName + ']' + @strOrder + ') as tblTmp)'
??????????????????????? + @strOrder

?????????? if @strWhere != ''
???????????? set @strSQL = 'select top ' + str(@PageSize) +' '+@strGetFields+ ' from ['
??????????????????????? + @tblName + '] where [' + @fldName + ']' + @strTmp + '(['
??????????????????????? + @fldName + ']) from (select top ' + str((@PageIndex-1)*@PageSize) + ' ['
??????????????????????? + @fldName + '] from [' + @tblName + '] where ' + @strWhere + ' '
??????????????????????? + @strOrder + ') as tblTmp) and ' + @strWhere + ' ' + @strOrder
???????? end
?? end
exec (@strSQL)
--print @strSQL
GO

存儲過程分頁